Audi R8 Gen 1 (2006-2015) | Prepreg Dry Carbon Fiber LBW Wide-Body Side Skirts

Audi R8 Gen 1 (2006-2015) Prepreg Dry Carbon Fiber LBW Wide-Body Side Skirts

Engineered for Audi R8 Gen 1 (2006-2015) owners running the LBW wide-body series, this Prepreg (Dry) Carbon Fiber LBW Side Skirt set adds track-grade wide-body character to your mid-engine supercar's profile. Made to factory-spec mounting tolerances by leading manufacturers around the world and quality-controlled by BYC Performance, this Audi R8 LBW carbon side skirt bolts to OEM rocker mounting points and shares its visual language with the rest of the LBW set.

If you're building a serious Audi R8 wide-body project and need side skirts that exceed the factory units, manage underbody airflow, and tie together the LBW front lip and rear diffuser, this dry carbon LBW side skirt is built for you. Autoclave-cured prepreg carbon fiber delivers noticeably lighter weight than wet-lay carbon parts. Engineered to complement the LMS racing DNA of the Gen 1 R8's 4.2L V8 FSI (420 hp) and 5.2L V10 FSI engines (V10 525 hp, V10 Plus 550 hp, R8 GT 560 hp), the aggressive side profile cleans up underbody airflow at speed.

Key Features

• Prepreg (Dry) Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure; a more consistent weave.
• Wide-Body Coordinated Profile: Shares visual language with the rest of the LBW set (front lip, rear diffuser, spoiler); noticeably wider and more aggressive than the OEM rocker.
• Aerodynamic Side Profile: Optimized lower edge geometry reduces side-body turbulence and channels underbody airflow.
• Significant Weight Savings: Noticeably lighter than the factory plastic skirt.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern under a high-gloss UV-protective clear coat.
• OEM Mounting Points: Direct fit to standard Gen 1 rocker clips and bolt points; the skirt itself does not require fender cutting.
• UV & Chemical Protection: Long-life clear coat protects against fading, cracking, and roadside tar splash.

Prepreg (Dry) Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature, leaving air voids and inconsistent weight. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

Installing the Audi R8 LBW carbon side skirt is a direct replacement of the factory part. Professional installation is recommended:

1. Raise the vehicle and remove the OEM rocker clips and bolts.
2. Carefully detach the original side skirt.
3. Test-fit the new carbon LBW skirt; verify alignment at the front and rear bumper seams.
4. Secure with supplied clip and bolt hardware.
5. Clean surfaces with alcohol; apply 3M VHB reinforcement where specified.
6. If running the full LBW set, verify panel alignment with adjoining parts.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface. Mind curb strikes during low-speed maneuvering.

FAQ

Does this fit the Audi R8 Gen 2 (2015-2024)?
No. The R8 Gen 1 and Gen 2 have completely different chassis and rocker geometry.

Does the wide-body look require fender cutting?
The skirt itself does not require fender cutting; it bolts to standard Gen 1 rocker mounting points. However, the LBW aesthetic pairs best with wider wheel offsets and tire packages. Verify tire clearance if applicable.

Compatible with the standard (non-LBW) Gen 1?
Yes, this skirt mounts to the standard Gen 1 rocker while sharing the LBW kit's wide-body visual language.

Difference between V8 4.2 and V10 5.2 fitment?
None. All Gen 1 trims share the same rocker mounting points.

Compatible with Audi R8 Spyder?
Yes, Spyder Gen 1 shares the same rocker geometry.

Compatible with Lamborghini Gallardo?
No. R8 Gen 1 and Gallardo have different rocker designs.

Will rain damage dry carbon parts?
No. Autoclave-cured prepreg carbon is fully waterproof.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available. Parts sourced to order are delivered within 30 days of the order date at the latest.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world and supplying them to the Turkish market. Our catalog includes Audi R8 carbon parts, Audi RS carbon parts, BMW M3 carbon side skirts, Porsche carbon parts, and many more high-quality carbon components.