BMW M2 F87 Prepreg Dry Carbon Fiber Rear Bumper

Engineered for BMW M2 F87 owners who want a full-replacement rear-end transformation, this Prepreg Dry Carbon Fiber Rear Bumper redefines the rear of your vehicle with an integrated diffuser and aggressive lines. Manufactured in Europe to factory-spec mounting tolerances and quality-controlled by BYC Performance, this BMW M2 F87 carbon rear bumper bolts directly to OEM mounting points — your existing PDC sensors and rear camera transfer over.

If you're building a serious BMW M2 F87 tuning project and want to replace the entire factory plastic bumper, this dry carbon rear bumper is built for you. Autoclave-cured prepreg carbon fiber is noticeably lighter than wet-lay carbon parts, with a more consistent weave and outstanding long-term UV resistance. Designed to complement the N55-powered M2 (370 hp) and the S55-powered M2 Competition / CS (410-444 hp), it is noticeably lighter than the OEM plastic bumper.

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure for a more consistent weave.
• Full-Replacement Bumper: Complete rear bumper swap with an integrated diffuser and more aggressive contours.
• PDC & Camera Compatible: Pre-cut PDC sensor holes and rear-camera mounting ready.
• High Strength: Carbon fiber offers very high strength for its weight.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under a high-gloss UV-protective clear coat.
• OEM Mounting Points: Direct bolt-on to factory F87 brackets, no cutting or drilling.
• Weight Savings: Noticeably lighter than the OEM plastic bumper.

Prepreg Dry Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg dry carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → noticeably lighter and more consistent
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This BMW M2 F87 rear bumper fits the following models perfectly:

• BMW M2 Coupé F87 (2016, 2017, 2018) — N55 engine (~370 hp)
• BMW M2 Competition F87 (2018, 2019, 2020, 2021) — S55 engine (~410 hp)
• BMW M2 CS F87 (2020, 2021 — limited edition) — S55 engine (~444 hp)

NOTE: This bumper is NOT compatible with the new-generation BMW M2 G87 (2023+). G87 has a different chassis geometry. A separate G87 carbon part range is available in our catalog.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Origin: Europe

Installation Notes

Installing the BMW M2 F87 carbon rear bumper is a full replacement of the OEM bumper. Professional installation is strongly recommended:

1. Raise the vehicle; remove rear tail-light trims and underbody panels.
2. Detach the OEM bumper from bolts and clips; remove PDC sensors and camera.
3. Transfer sensors, camera, and brackets into the carbon bumper.
4. Test-fit the carbon bumper, then secure with side and underbody bolts to the manufacturer's recommended torque.
5. Reconnect and verify PDC and camera function.
6. Confirm exhaust tips are centered in the cutouts.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface.

FAQ

Is this bumper compatible with OEM parking sensors and camera?
Yes. Pre-cut PDC sensor holes and camera mounting are ready; existing electronics transfer over.

Does this fit the BMW M2 G87 (2023+)?
No. F87 and G87 have different chassis codes and rear bumper geometry. A separate carbon bumper is available for G87.

Compatible with both M2 base (N55) and M2 Competition (S55)?
Yes. This bumper fits all F87 variants: 2016-2018 M2 Coupé (N55), 2018-2021 M2 Competition (S55), and M2 CS (S55). Bracket geometry is consistent across F87 trims.

Can the bumper be painted?
Usually left as exposed weave; if desired it can be painted after proper primer and surface preparation.

Shipping time?
In-stock items ship within 1-3 business days via partner couriers. International shipping available.

Warranty?
BYC Performance offers a 12-month manufacturer warranty on this product.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers and supplying them to the Turkish market. Our catalog includes BMW M2 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components.