Audi S4 / A4 / RS4 B9 / B9.5 | Prepreg Dry Carbon Fiber Vented Hood

Audi S4/A4/RS4 B9/B9.5 (2015-2023) Prepreg Dry Carbon Fiber Vented Hood

Engineered for Audi S4/A4/RS4 B9 and B9.5 (2015-2023) sedan and Avant owners, this Prepreg Dry Carbon Fiber Vented Hood replaces the factory steel hood and delivers race-grade aerodynamics with substantial weight savings. Imported from leading manufacturers around the world and quality-controlled by BYC Performance, this Audi B9 carbon hood bolts directly to OEM hinge, latch, and washer points: no cutting, drilling, or modification required.

If you're building a serious Audi S4 B9 tuning, A4 B9.5 modifying, or RS4 B9 modifying project and need a real performance hood that reduces engine-bay heat and front-axle mass, this dry carbon vented hood is built for you. Autoclave-cured prepreg carbon is noticeably lighter than the factory steel hood, sharpening front-end response and turn-in feel. The functional vents directly aid heat rejection from the RS4 B9's 2.9 TFSI V6 biturbo (EA839) 444 hp engine, shared with the Porsche Panamera 4S, and the S4's 3.0 TFSI V6 single-turbo.

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated plies cured in an autoclave under high heat and pressure for a more consistent weave.
• Vented Design: Functional outlets reduce engine-bay temperatures and high-speed pressure buildup.
• Significant Weight Savings: Versus the factory steel hood, reduces front-axle mass and sharpens steering feel.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight. Autoclave-cured race-spec durability.
• Dual-Skin Construction: Inner support panel preserves torsional rigidity and matches the structural behavior of the OEM hood.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under a high-gloss UV-protective clear coat on the outer skin.
• Direct OEM Fit: Plug & play on Audi A4 / S4 / RS4 B9 and B9.5 (2015-2023) sedan and Avant factory hinge, gas-strut, and latch mounting points.

Prepreg Dry Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts use wet lay-up, with resin applied by hand and cured at room temperature. Prepreg dry carbon:

• Autoclave-cured under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

Installation requires removing the original hood and refitting on the OEM hinges. Professional installation is strictly required.

1. Support the hood in open position and remove the gas struts.
2. Disconnect washer hoses and detach the insulating mat from the OEM hood.
3. Loosen hinge bolts and lift off the original hood (two people required).
4. Align the carbon hood on the hinges with hardware loosely fitted.
5. Set even gaps to bumper, headlights, and fenders, balanced left-to-right.
6. Tighten hinge bolts in stages to the manufacturer's recommended torque. Refit washer hoses and any insulation.
7. Verify safety catch and primary latch function correctly.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface. Periodically check and clean the inner vent surfaces.

FAQ

Is this hood compatible with the RS4?
Yes. A4, S4, and RS4 B9/B9.5 share the same engine-bay structure and hood hinge layout; this hood fits all three trims.

Does this hood fit both B9 and B9.5?
Yes. The B9.5 facelift updated only the bumpers and headlights: the engine-bay structure and hood hinge points are unchanged.

Compatible with A4 Avant and RS4 Avant?
Yes. Sedan and Avant share the same front engine-bay geometry. Note: the B9 RS4 was produced globally only as an Avant.

Compatible with A5/S5/RS5 (B9)?
No. The A5 family (Coupé/Sportback/Cabriolet) uses a different hood. A separate A5-family carbon hood is available in our catalog.

Compatible with previous-generation B8/B8.5?
No. B8/B8.5 (2008-2015) is an entirely different platform.

Are the vents functional or cosmetic?
Functional. The outlets vent hot engine-bay air and relieve high-speed pressure buildup.

Shipping time?
In-stock items ship within 1-3 business days via partner couriers. International shipping available. Parts sourced to order are delivered within 30 days of the order date at the latest.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world and supplying them to the Turkish market. Our catalog includes Audi B9 carbon parts, Audi RS carbon diffusers, BMW M3 carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components. All parts are sourced from leading manufacturers around the world and undergo strict quality control.