BMW M2 F87 Prepreg Dry Carbon Fiber MTC Front Lip

Engineered for BMW M2 F87 owners who want a deep, motorsport-inspired alternative to the MP and CS profiles, this Prepreg Dry Carbon Fiber MTC Front Lip sharpens the front fascia and adds genuine high-speed front-axle stability. Manufactured in Europe to factory-spec mounting tolerances and quality-controlled by BYC Performance, this BMW M2 F87 carbon MTC front lip bolts directly to OEM bumper clips — no cutting or drilling required.

If you're building a serious BMW M2 F87 tuning project and want an aggressive, distinctive front lip profile, this dry carbon MTC front lip is the answer. Autoclave-cured prepreg carbon fiber is noticeably lighter than wet-lay carbon parts, with strong structural integrity and outstanding long-term UV resistance. Designed to complement the N55-powered M2 (370 hp) and the S55-powered M2 Competition / CS (410-444 hp).

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure for homogeneous resin distribution and a more consistent weave.
• MTC Styling: Motorsport-inspired deep lip profile, an alternative to MP and CS designs.
• Aerodynamic Balance: Reduces front-axle lift at speed and adds downforce.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play installation on factory M2 F87 bumper lower edge.
• UV & Chemical Protection: Long-life clear coat protects against fading, cracking, fuel splash, and road tar.

Prepreg Dry Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg dry carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and more consistent structure
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This BMW M2 F87 MTC front lip fits the following models perfectly:

• BMW M2 Coupé F87 (2016, 2017, 2018) — N55 engine (~370 hp)
• BMW M2 Competition F87 (2018, 2019, 2020, 2021) — S55 engine (~410 hp)
• BMW M2 CS F87 (2020, 2021 — limited edition) — S55 engine (~444 hp)

NOTE: This MTC lip is NOT compatible with the new-generation BMW M2 G87 (2023+). G87 has a different bumper geometry.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Origin: Europe

Installation Notes

Installing the BMW M2 F87 carbon MTC front lip is a clip-and-bolt attachment to the lower bumper. Professional installation is recommended:

1. Raise the vehicle and clean the bumper lower edge.
2. Test-fit the lip and mark fastener locations.
3. Secure with supplied clips and bolts to the manufacturer's recommended torque.
4. Check side-edge alignment for a flush fit.
5. Verify the lip sits evenly along its full length.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface.

FAQ

Does the MTC front lip bolt to the OEM M2 F87 bumper?
Yes. All F87 front bumpers share the same lower geometry; the lip attaches with clips and bolts directly to the OEM bumper edge.

Does this fit the BMW M2 G87 (2023+)?
No. F87 and G87 have different chassis codes and bumper geometry. A separate carbon lip is available for G87.

Compatible with both M2 base (N55) and M2 Competition (S55)?
Yes. The lip fits all F87 variants: 2016-2018 M2 Coupé (N55), 2018-2021 M2 Competition (S55), and M2 CS (S55).

What's the difference between MTC, MP, and CS lips?
MP is the classic M Performance silhouette, CS is the limited-edition deep profile, and MTC is a motorsport-inspired alternative deep profile. All three bolt to the same OEM clips.

Shipping time?
In-stock items ship within 1-3 business days via partner couriers. International shipping available.

Warranty?
BYC Performance offers a 12-month manufacturer warranty on this product.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers and supplying them to the Turkish market. Our catalog includes BMW M2 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components.