BMW M2 F87 Prepreg Dry Carbon Fiber Plexi-Window Hood

Engineered with motorsport intent for BMW M2 F87 owners, this Prepreg Dry Carbon Fiber Plexi-Window Hood transforms the front of the car with aggressive GTS-spec aesthetics while exposing the engine bay through a transparent polycarbonate insert. Manufactured in Europe and quality-controlled by BYC Performance, this BMW M2 F87 plexi carbon hood bolts directly to OEM hinges and gas-strut points — a true direct replacement for the factory steel hood.

If your BMW M2 F87 tuning project needs both heat extraction and a striking visual statement, this dry carbon plexi-window hood is unmatched. The central polycarbonate window puts the engine bay on display while the surrounding carbon vents extract hot air at speed. On both the S55-powered M2 Competition / CS (410-444 hp) and the N55-powered M2 Coupé (370 hp), it delivers measurable IAT (intake air temp) reduction during track use.

Key Features

• Clear Polycarbonate Window: High-impact, UV-protected polycarbonate insert showcases the engine bay.
• Integrated Air Channels: Channels around the window optimize hot air extraction from the engine bay.
• Prepreg Dry Carbon Technology: Autoclave-cured under high heat and pressure for a consistent weave.
• Noticeable Weight Savings: Noticeably lighter than the OEM steel hood; reduces front axle weight.
• OEM Hinge & Gas Strut Compatibility: Factory hinge mounts, gas struts, and hood latch bolt up directly.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play installation with no cutting or drilling.

Prepreg Dry Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg dry carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → noticeably lighter with very high strength for its weight
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This BMW M2 F87 plexi hood fits the following models perfectly:

• BMW M2 Coupé F87 (2016, 2017, 2018) — N55 engine (~370 hp)
• BMW M2 Competition F87 (2018, 2019, 2020, 2021) — S55 engine (~410 hp)
• BMW M2 CS F87 (2020, 2021 — limited edition) — S55 engine (~444 hp)

NOTE: This hood is NOT compatible with the new-generation BMW M2 G87 (2023+). G87 has different front-end geometry.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave) + UV-protected Polycarbonate Insert
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black + clear polycarbonate
• Style: Central plexi insert + perimeter air channels
• Origin: Europe

Installation Notes

Installing the BMW M2 F87 plexi carbon hood requires complete removal of the OEM hood. Professional installation is strongly recommended:

1. Open the hood and disconnect windshield washer hoses.
2. Disconnect gas struts on both sides.
3. With two people, loosen hinge bolts and lift off the OEM hood.
4. Install the carbon hood on hinges and adjust panel gaps (~5 mm front, ~4 mm sides).
5. Fine-tune hood stop bumpers so height is flush with fenders.
6. Carefully remove protective film from the plexi window after installation.

Care & Maintenance

Wash carbon surface with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Clean the polycarbonate window with a soft microfiber and plastic polish; avoid abrasive chemicals.

FAQ

Will the plexi window yellow from UV or rain?
No. The insert is UV-protected, high-impact polycarbonate with strong long-term yellowing and crack resistance.

Does this fit the BMW M2 G87 (2023+)?
No. F87 and G87 have different chassis codes and front-end geometry.

Compatible with both M2 base (N55) and M2 Competition (S55)?
Yes. All F87 variants (N55 Coupé, S55 Competition, S55 CS) share the same hood hinge geometry.

Does it save weight?
Yes. It is noticeably lighter than the OEM steel hood.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available.

Warranty?
BYC Performance offers a 12-month warranty.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers and supplying them to the Turkish market. Our catalog includes BMW M2 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components. All parts undergo strict quality control.