BMW M2 F87 | Prepreg Dry Carbon Fiber Vented Hood

BMW M2 F87 Prepreg Dry Carbon Fiber Vented Hood

Engineered for BMW M2 F87 owners chasing racing-grade aesthetics and real cooling gains, this Prepreg Dry Carbon Fiber Vented Hood brings aggressive track styling to your front end while actively extracting hot air from the engine bay. Imported from leading manufacturers around the world and quality-controlled by BYC Performance, this BMW M2 F87 carbon hood fits OEM hinge and gas strut points perfectly.

If you're building a serious BMW M2 F87 tuning project and need a part that delivers both substantial weight savings and thermal performance, this dry carbon vented hood is built for you. Autoclave-cured prepreg carbon is noticeably lighter than the OEM steel hood, sharpening steering feel. Effective heat extraction supports both the N55-powered M2 (370 hp) and the S55-powered M2 Competition / CS (410-444 hp), especially during track sessions.

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure for a more consistent weave.
• Functional Vents: Extract hot air from the engine bay; reduce heat soak during track use.
• Noticeable Weight Reduction: Noticeably lighter than the OEM steel hood; meaningful front-axle weight savings.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under a high-gloss UV-protective clear coat.
• OEM Hinge Compatible: Direct fit on factory hinges and gas struts.
• High Strength: Carbon fiber offers very high strength for its weight.
• UV & Chemical Protection: Long-life clear coat resists fading, cracking, and bug splatter.

Prepreg Dry Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature, leaving air voids and inconsistent weight. Prepreg dry carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → noticeably lighter with very high strength for its weight
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

Installing the BMW M2 F87 carbon hood requires professional installation. Steps:

1. Remove the heat insulation pad and detach gas struts from the OEM hood.
2. With a helper, unbolt the hood from the hinges and lift it off.
3. Loosely mount the new carbon hood to the hinges.
4. Adjust panel gaps so the hood aligns symmetrically with fenders and headlights.
5. Torque hinge bolts to the manufacturer's recommended torque and reconnect gas struts.
6. Apply heat insulation tape around the vent openings if needed.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface. Do not wash while the engine is hot.

FAQ

Are the vents functional?
Yes. They extract hot air from the engine bay and reduce heat soak, especially on track.

Does this fit the BMW M2 G87 (2023+)?
No. F87 and G87 have different chassis and hood hinge geometry.

Compatible with both M2 base (N55) and M2 Competition (S55)?
Yes. Hood hinge geometry is consistent across all F87 trims.

How does this differ from the CS vented hood?
The CS hood takes its layout from the limited-edition M2 CS, with a single wide central vent. The standard vented hood uses symmetrical side vents for a classic tuning aesthetic.

Are OEM hood sensors reused?
Yes. Hood-ajar sensor, hinges, and gas struts transfer from the original hood.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world and supplying them to the Turkish market. Our catalog includes BMW M2 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components. All parts undergo strict quality control.