BMW M5 F90 Prepreg Dry Carbon Fiber MP Front Lip Splitter

Engineered for BMW M5 F90 owners inspired by the M Performance catalog, this Prepreg (Dry) Carbon Fiber MP Front Lip Splitter adds a sharp, aggressive extension to your sedan's front bumper while contributing to front-axle aero. Manufactured in Europe to factory-spec mounting tolerances and quality-controlled by BYC Performance, this BMW M5 F90 carbon front lip bolts directly to OEM bumper clip and bolt points — no cutting, no drilling, no modification required.

If you're building a serious BMW M5 F90 tuning project and need a part that brings M Performance character to the factory bumper, this dry carbon front lip is built for you. Autoclave-cured prepreg carbon fiber is noticeably lighter than wet-lay carbon parts, offers very high strength for its weight, and delivers outstanding long-term UV resistance. Engineered to match the aggressive character of the S63B44T4-powered F90 M5 — 600 hp standard and 617 hp Competition — this lip is the ideal aesthetic and functional upgrade for both highway and track use.

Key Features

• Prepreg (Dry) Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure ensure a consistent weave.
• M Performance Styling: Prepreg carbon version of the OEM F90 M5 MP front lip design. Adds a sharp extension to the factory bumper.
• Front-Axle Aero: Optimized lip profile directs airflow at the front end at high speed and contributes to throttle response.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight. Resists stone chips and light curb contact.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play installation on factory F90 M5 (pre-LCI) bumper clip and bolt points.
• UV & Chemical Protection: Long-life clear coat protects against fading, cracking, fuel splash, and road tar.

Prepreg (Dry) Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This BMW M5 F90 front lip fits the following models perfectly:

• BMW M5 F90 Sedan (2018, 2019, 2020) — S63B44T4 V8 (600 hp)
• BMW M5 Competition F90 (2019, 2020) — S63 (617 hp)

Important notes:

• This product is NOT compatible with the F90 LCI (2021+ facelift). LCI has different front bumper geometry; a separate LCI carbon lip is available in our catalog.
• This product is NOT compatible with BMW M5 F10 (previous-generation 2011-2017) or BMW M5 G90 (new-generation 2024+ hybrid).
• This product is NOT compatible with BMW M3 F80 / M4 F82 or BMW M3 G80 / M4 G82 — the M3/M4 family has different bumper geometry.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Origin: Europe

Installation Notes

Installing the BMW M5 F90 carbon front lip is a direct add-on to the lower face of the bumper. Professional installation is recommended:

1. Clean the lower bumper surface with isopropyl alcohol and dry.
2. Test-fit the carbon lip dry (center alignment is critical — equal gap left/right).
3. Secure with supplied 3M double-sided tape or hardware kit.
4. If using screws, fasten to OEM under-bumper clip points to the manufacturer's recommended torque.
5. Check ground clearance below the lip; take extra care over curbs and steep ramps.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from the surface. Avoid curb scrapes — the front lip becomes the lowest point of the vehicle.

FAQ

Does this fit the F90 LCI (2021+)?
No. The F90 LCI facelift has different front bumper geometry. A separate carbon front lip for the LCI is available in our catalog.

Compatible with both standard M5 and M5 Competition?
Yes. This lip fits both 2018-2020 standard M5 F90 (600 hp) and 2019-2020 M5 Competition F90 (617 hp) — front bumper geometry is identical across pre-LCI F90 trims.

Is this the same as the BMW M5 F10?
No. M5 F10 (2011-2017) is the previous generation with completely different front bumper. A separate carbon lip for the F10 is available.

Does it fit BMW M3 F80 / M4 F82?
No. M3 F80 and M4 F82 have different chassis and bumper geometry. Separate F-series M3/M4 carbon lips are available.

Will ground clearance decrease?
Yes. The lip becomes the lowest point of the vehicle; approach curbs and steep ramps carefully.

Will rain damage dry carbon parts?
No. Autoclave-cured prepreg carbon is fully waterproof and weather-resistant.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available.

Warranty?
BYC Performance offers a 12-month manufacturer warranty on this product.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers and supplying them to the Turkish market. Our catalog includes BMW M5 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components. All products undergo strict quality control.