Audi R8 Gen 2 (2015-2018) Prepreg Dry Carbon Fiber Front Lip

Engineered for Audi R8 Gen 2 (2015-2018) owners, this Prepreg Dry Carbon Fiber Front Lip (standard profile) upgrades the front bumper of your supercar with a clean, aggressive, track-grade appearance while contributing front-axle downforce at speed. Manufactured in Europe to factory-spec mounting tolerances and quality-controlled by BYC Performance, this Audi R8 carbon front lip bolts directly to OEM mounting points — no cutting, no drilling, no modification required.

If you're building a serious Audi R8 tuning project and need a part that exceeds the factory front lip in both look and finish, this dry carbon front lip is built for you. Autoclave-cured under high heat and pressure, prepreg carbon fiber is noticeably lighter than wet-lay parts and offers outstanding long-term UV resistance. Engineered with a clean standard profile to complement the LMS racing DNA of the Gen 2 R8's 5.2L V10 FSI naturally-aspirated engine (V10 540 hp, V10 Plus 610 hp).

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated carbon plies autoclave-cured under high heat and pressure for a more consistent weave.
• Standard Profile Design: Unlike the V Front Lip's aggressive V-cut, this is a cleaner, flatter underbumper profile — close to OEM lines but elevated with carbon fiber finish.
• Lightweight: Noticeably lighter than the factory plastic part — reduces front-axle weight.
• High Strength: Very high strength for its weight. Resists stone chips and curb scrapes.
• Aerodynamic Contribution: Channels front underbody airflow to reduce front-axle lift at high speed.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play installation on factory Audi R8 Gen 2 (2015-2018) mounting points.

Prepreg (Dry) Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving weave and weight that vary part to part. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This Audi R8 front lip fits the following models perfectly:

• Audi R8 Coupé Gen 2 (2015, 2016, 2017, 2018) — V10 5.2L FSI (540 hp)
• Audi R8 V10 Plus Gen 2 (2015-2018) — V10 5.2L (610 hp)
• Audi R8 Spyder Gen 2 (2015-2018) — V10 5.2L FSI
• Audi R8 RWS (Rear-Wheel Series, 2018) — V10 5.2L (540 hp)

Important notes:

• NOT compatible with the previous-generation Audi R8 Gen 1 (2006-2015). Different front bumper geometry.
• NOT compatible with the post-facelift Audi R8 Gen 2 Facelift (2019-2024). The 2019 facelift changed the front bumper geometry.
• NOT compatible with the Lamborghini Huracán — shared MLBevo platform but different front bumper geometry.
• This standard Front Lip differs from the V Front Lip — a separate aggressive V-cut variant is available in our catalog.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Origin: Europe

Installation Notes

Installing the Audi R8 carbon front lip is a direct replacement of the factory part. Professional installation is recommended:

1. Raise the vehicle and remove front bumper underbody screws.
2. If equipped, detach the OEM lower lip from clips.
3. Test-fit the carbon front lip for alignment.
4. Secure with supplied hardware and 3M VHB tape (torque: 6-8 Nm).
5. Verify left/right symmetry and minimum ground clearance (10 cm).

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface.

FAQ

What's the difference between Front Lip and V Front Lip?
The standard Front Lip has a clean, flat underbumper profile close to OEM lines. The V Front Lip features an aggressive center V-cut inspired by motorsport splitters. Both use the same OEM mounting points — choice is aesthetic.

Does this fit the Audi R8 Gen 1 (2006-2015)?
No. Different front bumper geometry.

Does this fit the post-facelift 2019-2024 R8?
No. The 2019 facelift changed front bumper geometry. Separate post-facelift version available.

Compatible with Lamborghini Huracán?
No. Shared MLBevo platform but different front bumper geometry.

Compatible with Audi R8 Spyder (Convertible)?
Yes — Audi R8 Spyder Gen 2 (2015-2018) is fully compatible.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available.

Warranty?
BYC Performance offers a 12-month warranty.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers. Our catalog includes Audi R8 carbon parts, Audi RS carbon diffusers, BMW M3 carbon diffusers, Porsche carbon spoilers, and many more high-quality carbon components. Every part undergoes strict quality control.