Audi R8 Gen 2 (2015-2018) Prepreg Dry Carbon Fiber V Front Lip

Engineered for Audi R8 Gen 2 (2015-2018) owners who demand racing-grade quality, this Prepreg Dry Carbon Fiber V Front Lip upgrades the front bumper of your supercar with an aggressive V-cut profile inspired by the R8 LMS race car splitter, while contributing front-axle downforce at speed. Manufactured in Europe to factory-spec mounting tolerances and quality-controlled by BYC Performance, this Audi R8 V carbon front lip bolts directly to OEM mounting points — no cutting, no drilling, no modification required.

If you're building a serious Audi R8 tuning project and need a part that exceeds the factory front lip in both performance and finish, this dry carbon V front lip is built for you. Autoclave-cured prepreg carbon fiber is noticeably lighter than wet-lay parts, with far superior structural integrity, and outstanding long-term UV resistance. Engineered to match the LMS racing DNA of the Gen 2 R8's 5.2L V10 FSI naturally-aspirated engine (V10 540 hp, V10 Plus 610 hp).

Key Features

• Prepreg (Dry) Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure ensure homogeneous resin distribution and a more consistent weave.
• V-Cut Aggressive Design: Distinct V-shaped center cutout — inspired by R8 LMS front splitter. Differs from the standard Front Lip profile.
• Lightweight: Noticeably lighter than the factory plastic part — reduces front-axle weight.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight. Resists stone chips and curb scrapes.
• Aerodynamic Contribution: Channels front underbody airflow to reduce front-axle lift at high speed and contribute downforce.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play installation on factory Audi R8 Gen 2 (2015-2018) mounting points.

Prepreg (Dry) Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This Audi R8 V front lip fits the following models perfectly:

• Audi R8 Coupé Gen 2 (2015, 2016, 2017, 2018) — V10 5.2L FSI (540 hp)
• Audi R8 V10 Plus Gen 2 (2015-2018) — V10 5.2L (610 hp)
• Audi R8 Spyder Gen 2 (2015-2018) — V10 5.2L FSI
• Audi R8 RWS (Rear-Wheel Series, 2018) — V10 5.2L (540 hp)

Important notes:

• NOT compatible with the previous-generation Audi R8 Gen 1 (2006-2015). Different front bumper geometry.
• NOT compatible with the Audi R8 Gen 2 Facelift (2018-2024). The 2019 facelift changed the front bumper geometry.
• NOT compatible with the Lamborghini Huracán — shared MLBevo platform but different front bumper geometry.
• The V Front Lip is a distinct aggressive variant — a separate standard Front Lip is also available in our catalog.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Origin: Europe

Installation Notes

Installing the Audi R8 V carbon front lip is a direct replacement of the factory part. Professional installation is recommended:

1. Raise the vehicle and remove front bumper underbody screws.
2. If equipped, detach the OEM lower lip from clips.
3. Test-fit the carbon V lip for alignment.
4. Secure with supplied hardware and 3M VHB tape to the manufacturer's recommended torque.
5. Verify left/right symmetry and minimum ground clearance (10 cm).

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface.

FAQ

What's the difference between V Front Lip and standard Front Lip?
The V Front Lip features an aggressive center V-cut inspired by motorsport splitters. The standard Front Lip has a flatter, classic underbumper profile. Both use the same OEM mounting points — choice is aesthetic.

Does this fit the Audi R8 Gen 1 (2006-2015)?
No. Different front bumper geometry.

Does this fit the Gen 2 Facelift (2018-2024)?
No. The 2019 facelift changed front bumper geometry. Separate Gen 2 Facelift version available.

Compatible with Lamborghini Huracán?
No. Shared MLBevo platform but different front bumper geometry.

Compatible with Audi R8 Spyder (Convertible)?
Yes — Audi R8 Spyder Gen 2 (2015-2018) is fully compatible.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available.

Warranty?
BYC Performance offers a 12-month warranty.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers. Our catalog includes Audi R8 carbon parts, Audi RS carbon diffusers, BMW M3 carbon diffusers, Porsche carbon spoilers, and many more high-quality carbon components. BYC sources its parts from leading European manufacturers, and every item undergoes strict quality control.