Audi R8 Gen 2 (2015-2024) | Prepreg Dry Carbon Fiber Vented Hood

Audi R8 Gen 2 (2015-2024) Prepreg Dry Carbon Fiber Vented Hood

Engineered for Audi R8 Gen 2 (2015-2024) owners who demand racing-grade quality, this Prepreg (Dry) Carbon Fiber Vented Hood delivers an aggressive, functional upgrade aligned with the R8's mid-engine supercar DNA. Made to factory mounting tolerances by leading manufacturers around the world and quality-controlled by BYC Performance, this Audi R8 carbon hood bolts directly to OEM hinges and latch: no cutting, no drilling, no modification required. The integrated vents reduce engine-bay heat and add genuine race-car aesthetic to the front end.

If you're building a serious Audi R8 tuning project and need a part that surpasses the factory aluminum hood in both performance and finish, this dry carbon vented hood is the answer. Autoclave-cured prepreg carbon fiber delivers noticeably lighter weight than the OEM aluminum hood, lowering load on the front axle for sharper turn-in and improved steering feel. Tuned to match the LMS racing DNA of the Gen 2 R8's 5.2L V10 FSI naturally-aspirated engine (V10 540 hp / V10 Plus 610 hp / V10 Performance 570-612 hp / R8 GT RWD 620 hp), the vented design is a visual and functional upgrade for both track and street.

Key Features

• Prepreg (Dry) Carbon Technology: Pre-impregnated carbon plies cured in autoclave under high heat and pressure, a more consistent weave, balanced resin distribution.
• Functional Vents: Integrated vent openings extract hot air from the engine bay, supporting the high-revving V10's thermal management.
• Significant Weight Savings: Noticeably lighter than the OEM aluminum hood; reduces front-axle load and improves front/rear balance.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight. Resists stone chips and vibration.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern with depth under a high-gloss UV-protective clear coat.
• Direct OEM Fit: Plug & play on factory Audi R8 Gen 2 (2015-2024) hinges and latch mechanism.
• UV & Chemical Protection: Long-life clear coat protects against fading, cracking, fuel splash, and road tar.

Prepreg (Dry) Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is hand-applied and room-temperature cured, leaving voids and inconsistent weight. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

Installing the Audi R8 carbon hood is a direct replacement of the OEM aluminum hood. Professional installation is strongly recommended:

1. Open the front section; secure the hood prop rod.
2. Mark hinge bolt positions and remove them; lift the hood carefully with two people.
3. Test-fit the carbon hood (gap alignment vs. fender and bumper).
4. Torque hinges to the manufacturer's recommended torque and adjust the latch.
5. Peel protective film from inside the vent openings.
6. Apply a ceramic-safe sealant before the first wash.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface. Periodically clean the inside of the vents with a soft brush.

FAQ

Does this fit both pre- and post-facelift R8?
Yes. The vented hood uses the same hinge and latch points on both Gen 2 generations; the 2019 facelift did not change hood geometry.

Does this fit the Audi R8 Gen 1 (2006-2015)?
No. R8 Gen 1 and Gen 2 have different chassis, hinges, and hood geometry.

Compatible with the Lamborghini Huracán?
No. The Huracán shares the MLBevo platform but uses a completely different hood and front-end geometry.

Compatible with the Audi R8 Spyder (Convertible)?
Yes. Spyder and Coupé share identical front hood mounting points.

Are the vents functional or cosmetic?
The vents are functional: they help extract hot air from the engine bay. The double-wall design prevents direct water intrusion onto engine components.

Will rain damage dry carbon parts?
No. Autoclave-cured prepreg carbon is fully waterproof and weather-resistant.

Shipping time?
In-stock items ship within 1-3 business days. International shipping available. Parts sourced to order are delivered within 30 days of the order date at the latest.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world. Our catalog includes Audi R8 carbon parts, Audi RS carbon diffusers, BMW M3 carbon diffusers, Porsche carbon spoilers, and many more high-quality components.