BMW M2 G87 | Prepreg Dry Carbon Fiber V Vented Hood

BMW M2 G87 Prepreg Dry Carbon Fiber V Vented Hood

Designed for BMW M2 G87 owners, this Prepreg Dry Carbon Fiber V Vented Hood replaces the factory steel hood with significant weight savings and functional heat extraction. Imported from leading manufacturers around the world and quality-controlled by BYC Performance, this BMW M2 G87 carbon hood bolts to OEM hinge points without modification.

The V-style vent geometry channels hot air out of the engine bay, helping stabilize engine and intercooler temperatures, especially on track. Autoclave-cured prepreg construction is noticeably lighter than the OEM steel hood. Engineered to match the visual aggression of the S58-powered 460 hp M2 G87, this is the ideal track-and-street upgrade.

Key Features

• Prepreg Dry Carbon Technology: Pre-impregnated plies cured in an autoclave under high heat and pressure for a more consistent weave.
• V Style Vents: Functional heat-extraction channels reduce engine-bay temperatures.
• Significant Weight Reduction: Noticeably lighter than the OEM steel hood.
• Reduced Front Axle Load: Lower hood mass sharpens steering feel.
• High Strength: Carbon fiber offers very high strength for its weight.
• 2x2 Twill Carbon Weave: Authentic carbon pattern under UV-protective clear coat.
• Direct OEM Fit: Compatible with factory hinges, latch, and gas struts.

Prepreg Dry Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature, which can leave air voids and inconsistent weight. Prepreg dry carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

Installing the BMW M2 G87 carbon hood is a full assembly swap. Two-person professional installation is required:

1. Open the hood and check the front cowl and any hinge-side cables.
2. Release the gas struts from both sides (helper must steady the hood).
3. Unbolt the hinges and lift the OEM hood horizontally clear.
4. Seat the carbon hood on the hinges and reconnect the gas struts.
5. Adjust panel gaps symmetrically left-to-right.
6. Test the latch and safety hook; torque the bolts to the manufacturer's recommended values.
7. TIP: The carbon hood is lighter, so OEM gas struts continue to hold it open properly.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer 30 cm from surface. Periodically clear leaves and debris from the inside of the vent openings.

FAQ

Will the vents let water into the engine bay?
No, V-style vents are directionally controlled with internal drip surfaces; normal driving and rain do not affect the engine bay.

Does this fit the BMW M2 F87 (2016-2021)?
No. G87 and F87 have different hood length and hinge geometry. A separate carbon hood is available for F87.

Is it compatible with the S58-powered M2 G87?
Yes, fits all M2 G87 trims (standard, Competition, the upcoming CS). M3 G80 / M4 G82 hoods are listed separately; bodywork is not shared.

Are the OEM gas struts strong enough?
Yes, the carbon hood is lighter, so the factory struts hold it open without issue.

Can it be painted?
Yes, if you prefer not to show the carbon weave, scuff-sand, prime, and paint to body color.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world and supplying them to the Turkish market. Our catalog includes BMW M2 carbon parts, BMW M3 carbon diffusers, Audi RS carbon hoods, Porsche carbon spoilers, and many more high-quality carbon components. All parts are sourced from leading manufacturers around the world and undergo thorough quality control.