Porsche Taycan (2019+) Prepreg Dry Carbon Fiber Front Lip

Engineered for Porsche Taycan J1 (2019+, first-gen electric sport sedan) owners, this motorsport-inspired Prepreg Dry Carbon Fiber Front Lip drops the front bumper line of your 800V electric sedan and reinforces the GT-electric character with an aggressive sport profile. Manufactured in Europe and quality-controlled by BYC Performance, this Porsche Taycan carbon front lip mounts to the OEM front bumper underside using 3M VHB tape and factory screw points — no permanent cutting required.

If you are building a Porsche Taycan tuning project and want a front-end aero piece that lowers the visual stance and channels airflow under the car, this dry carbon front lip is built for you. Autoclave-cured prepreg carbon fiber is noticeably lighter than wet-lay carbon parts, offers very high strength for its weight, and resists long-term UV fading. Visually matches the 800V dual-motor performance signature (Turbo S 750 hp launch, Turbo GT 2024+ 1019 hp launch, 0-100 km/h ~2.2 s).

Key Features

• Prepreg (Dry) Carbon Technology: Pre-impregnated carbon plies cured in an autoclave under high heat and pressure for a more consistent weave and balanced resin distribution.
• Aggressive Front Lip Profile: Sits under the front bumper to lower the visual stance with motorsport-inspired geometry.
• Race-Grade Strength: Carbon fiber offers very high strength for its weight. Resists stone chips and light contact.
• Aerodynamic Performance: Supports front-axle downforce behavior at speed.
• 2x2 Twill Carbon Weave: Authentic carbon fiber pattern under a high-gloss UV-protective clear coat.
• 3M VHB + Screw Mounting: Combines 3M VHB tape and OEM front-bumper underside screw points.
• Direct OEM Fit: Designed for the shared front bumper across Taycan Sedan, Cross Turismo, and Sport Turismo bodies.

Prepreg (Dry) Carbon vs. Wet Carbon — Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature — leaving air voids and inconsistent weight. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger for its weight
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Vehicle Fitment

This Porsche Taycan J1 carbon front lip fits the following models:

• Porsche Taycan Sedan J1 (2019-2024) — all trims
• Porsche Taycan Cross Turismo J1 (2021+) — shared front bumper
• Porsche Taycan Sport Turismo J1 (2022+) — shared front bumper
• Porsche Taycan / 4 / 4S / GTS / Turbo / Turbo S / Turbo GT J1

Important notes:

• Taycan is a single-generation (J1) model, so no previous-gen disclaimer applies.
• The Cross Turismo's raised-suspension package gives more ground clearance; on the Sedan the lip sits closer to the ground — approach high curbs and steep ramps with care.

Technical Specifications

• Material: Prepreg Carbon Fiber (2x2 Twill Weave)
• Manufacturing: Autoclave Cure
• Finish: High-Gloss Clear UV-Protective Resin
• Color: Natural carbon weave black
• Mounting: 3M VHB tape + OEM screw points
• Origin: Europe

Installation Notes

Installing the Porsche Taycan carbon front lip requires professional installation. General steps:

1. Clean the front bumper underside with isopropyl alcohol.
2. Test-fit the lip for alignment.
3. Peel the 3M VHB liner and place the lip.
4. Torque the screws at OEM points to the manufacturer's recommended torque.
5. Do not wash or drive at high speed for the first 48 hours.
6. Mind the lowered ground clearance over speed bumps and steep ramps.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon-safe sealant every 6 months. Keep pressure washer nozzle at least 30 cm from surface.

FAQ

Compatible with Cross Turismo / Sport Turismo?
Yes. Taycan Sedan, Cross Turismo, and Sport Turismo share the same front bumper.

Does the trim matter?
No. All Taycan J1 trims share the same front bumper geometry.

Does it replace the factory front spoiler?
No. The factory underbody splash guard is preserved; the lip sits below it.

Does it affect park sensors?
No. The lip sits under the bumper and does not cover sensor or camera cutouts.

Will rain damage dry carbon parts?
No. Autoclave-cured prepreg carbon is fully waterproof and weather-resistant.

Shipping time?
In-stock items ship within 1-3 business days. Long parts routed via a suitable carrier confirmed after order.

Warranty?
BYC Performance offers a 12-month manufacturer warranty on this product.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading European manufacturers and supplying them to the Turkish market. Our catalog includes Porsche carbon parts, Audi RS carbon diffusers, BMW M carbon diffusers, Porsche 911 carbon spoilers, and many more high-quality carbon components. All parts undergo strict quality control.