Porsche 911 Turbo S 991 / 991.2 | Prepreg Dry Carbon Fiber Stinger GTR Body Kit

Porsche 911 Turbo S 991 / 991.2 Prepreg Dry Carbon Fiber Stinger GTR Body Kit

Engineered specifically for the 991 Turbo S wide-body geometry, this Prepreg Dry Carbon Fiber Stinger GTR Body Kit brings a race-grade carbon package to one of the world's most capable daily GTs. Imported from leading manufacturers around the world and quality-controlled by BYC Performance, this Porsche 911 Turbo S Stinger GTR carbon body kit mounts directly to OEM Turbo S chassis points.

The 911 Turbo S 991 (560 hp) and 991.2 (580 hp), a 3.8L twin-turbo flat-6 with all-wheel drive and PDK, accelerates from 0-100 km/h in under 2.9 seconds and remains Porsche's daily-usable flagship. This Stinger GTR Body Kit delivers a complete aero and visual transformation for 991/991.2 Turbo S owners, including front bumper, splitter, side skirts, rear bumper, diffuser, and large rear wing. Autoclave-cured prepreg construction is noticeably lighter than OEM plastic bumper shells.

Key Features

• Prepreg Dry Carbon Technology: Autoclave-cured under high heat and pressure, a more consistent weave.
• Stinger GTR Aero Character: Cohesive design, wide front splitter, side flicks, aggressive rear wing, and diffuser.
• Turbo S-Specific Geometry: Molded specifically for 991/991.2 Turbo S wide-body geometry.
• Lightweight: Noticeably lighter than OEM plastic shells.
• Aerodynamic Gains: Optimized front splitter and rear wing improve high-speed stability.
• 2x2 Twill Carbon Weave: Authentic pattern under a high-gloss UV-protective clear coat.
• OEM-Compatible Mounting: Direct fit to factory Turbo S chassis/bumper points.

Prepreg Dry Carbon vs. Wet Carbon: Which Is Better?

Most aftermarket carbon parts are made using wet lay-up, where resin is applied by hand and cured at room temperature. Prepreg (dry) carbon:

• Cured in an autoclave under high heat and pressure → a more consistent weave
• A controlled resin ratio → lighter and stronger
• The production method widely chosen in motorsport
• Minimal UV fading over years of use

Installation Notes

The Stinger GTR body kit is a comprehensive install. Professional installation by an experienced carbon parts shop is strongly recommended.

1. Raise the vehicle and remove the front bumper (disconnect headlights, washer hoses, and parking sensors).
2. Remove side skirt mounting bolts.
3. Detach the rear bumper from behind the Turbo S exhaust system.
4. Dry-fit the new carbon panels and verify alignment with Turbo S wide-fender lines.
5. Secure with 3M VHB tape + supplied hardware to the manufacturer's recommended torque.
6. Mount the large rear wing to the support brackets to the manufacturer's recommended torque.
7. Adjust panel gaps and test parking sensors.

Care & Maintenance

Wash with pH-neutral car shampoo. Apply carbon sealant every 6 months. Keep pressure washer at least 30 cm from surface. Periodically inspect splitter and large wing for road debris and stone strikes.

FAQ

I own a standard Carrera or Carrera S. Is this kit compatible?
No. This kit is designed only for 991/991.2 Turbo S wide-body geometry. Carrera narrow-body geometry is different.

I own a Turbo (non-Turbo S). Is it compatible?
991/991.2 Turbo and Turbo S share most body geometry, but minor detail differences may apply. Confirm fitment with BYC Performance before ordering.

Does this kit fit the Porsche 911 992 Turbo S?
No. The 992 (2020+) has completely different bumper and panel geometry.

Does this kit fit the Porsche 911 997 Turbo S?
No. The 997 (2005-2012) is the previous generation.

Compatible with Cabriolet or Targa?
No. 991/991.2 Turbo S Coupé only.

What's included?
Typical Stinger GTR contents: front bumper (with splitter), side skirts, rear bumper (with diffuser), and large rear wing. Confirm detailed scope before ordering.

Does this kit deliver real aero performance?
Yes. The optimized front splitter and large rear wing improve axle balance and downforce distribution at high speed, visually and functionally complementing the Turbo S's sub-3-second 0-100 km/h performance.

Shipping time?
In-stock items ship within 1-3 business days; multiple oversized packages may apply. Parts sourced to order are delivered within 30 days of the order date at the latest.

Warranty?
Manufacturing defects are covered by a 24-month BYC warranty, in addition to your legal rights.

Why BYC Performance?

BYC Performance is a Turkey-based performance tuning specialist sourcing premium carbon fiber parts from leading manufacturers around the world and supplying them to the Turkish market. Our catalog includes Porsche 911 Turbo S carbon parts, Porsche carbon spoilers, Audi RS carbon diffusers, BMW M3 carbon hoods, and many more high-quality carbon components.